New Era Technique Private Limited

• Gaseous expansion system compensates for shrinkage and settlement in the plastic state.
• Can be pumped or poured into restricted locations.
• Highly fl uid to allow for placement without vibration.
• Pre-packed to overcome site-batched variations.
• Rapid strength gain to facilitate early reinstatement.
• High ultimate strengths and low permeability of cured repair.
• Contains no chloride admixture.
• Ensures piletop integrity as part of a waterproofi ng system

Nitobond EP is based on solvent-free epoxy resins containing pigments and fine fillers. It is supplied as a two-component material in pre-weighed quantities ready for on-site mixing and use. The ‘base’ component is white and the ‘hardener’ component is green, providing visual evidence that adequate mixing has been achieved.

Uses:

For bonding fresh wet cementitious materials to existing cementitious surfaces. For use on horizontal surfaces or on vertical surfaces where mortar or concrete can be supported by formwork. The long ‘open’ life makes it suitable for use with formwork or where additional steel reinforcement has to be fitted. The product is ideal for roads, bridges, pavements, loading bays and factories, and for bonded or granolithic floor toppings. Nitobond EP is equally suited to internal and external applications.

Advantages:

Nitobond EP may also be used as part of a repair system where a substrate/repair barrier is required or where the substrate is likely to remain permanently damp or wet.

•  Can be applied on to dry or damp substrates
•  Exhibits high mechanical strength
•  Positive adhesion - exceeds that of the tensile strength of the host concrete
•  Slow cure allows time to erect steel reinforcement and formwork
•  Solvent-free - can be used in enclosed locations

Renderoc Plug is supplied as a ready to use blend of dry powders which requires only the addition of clean water at site to produce a highly consistent, rapid setting mortar which is easy to apply in many diffi cult conditions. The material is based on a blend of cements, graded aggregates, special fillers and chemical additives which control the rate of set and minimise the risk of thermal cracking.

Uses :
For the rapid temporary patching and plugging of concrete segments, concrete and brick tunnel linings, sewage systems, below ground access chambers, pipes, basements, foundations and mines.
Advantages:

• Emergency water - stopping capability
• Single component - only the addition of clean water is required.
• Excellent bond to the substrate
• Low exotherm minimises thermal cracking
• Pre-packed formulation to overcome variation in site batching
• Contains no chloride admixtures

Advantages
1. Gaseous expansion system compensates for shrinkage and settlement in the plastic state 2. No metallic iron content to cause staining
3. Pre-packed material overcomes onsite batching variations
4. Develops high early strength without the use of chlorides
5. High ultimate strength ensure the durability of the hardened grout
6. Free flow ensures high level of contact with load bearing area

• Non metallic - does not rust or stain.
• Provides a hard, abrasion resistant surface.
• Forms monolithic bond with base concrete.
• Easy and economical to apply

Brushbond RFX is a two component acrylic polymer modified cementitious coating which consists of Brushbond RFX powder and Nitobond BBX acrylic emulsion. It requires only the addition of clean water at site to produce an easily brushable coating.

Uses:
Brushbond RFX is an high performance elastomeric cementitious coating used for waterproofing and to protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen & water. Brushbond RFX is suitable for all types of structures including those in coastal environments. The product can be used on concrete, brick and blockwork substrates and is equally suitable for new and existing structures. The product is designed to reface and even out variations in concrete and masonry surfaces and bridge shrinkage cracks. It provides a seamless, flexible waterproof coating suitable for water tanks, reservoirs, drainage culverts basements and roofs. The product provides a tough durable water resistant coating which can withstand light pedestrian traffic and also has excellent weather resistance for exterior applications.

Advantages:

• Excellent barrier to carbon dioxide, chloride and sulphate ions.
• Allows water vapour to escape from the structure.
• Waterproof-suitable for water retaining structures.
• High resistance to the effect of long-term weathering, durable in all climate conditions including UV attack.
• Non toxic - ideal for potable water tanks.
• Flexible, with thermal expansion similar to concrete.
• Excellent bond to concrete and masonry. 
• Good crack accommodation capacity. 
• Minimum surface preparation needed and low labour costs.

• Superior in performance over Sodium based systems
• ASR Protection - contains Lithium, the chemical element known to mitigate damaging ASR (Alkali-silica reactivity)
• Seals micro-channels in concrete against water penetration and chemical attack
• Hardens - making concrete stronger and abrasion resistant
• Dust proofs - creating a cleaner, healthier environment
• Permanent - One penetrating application
• Easy maintenance. Makes cleaning easier. Reduces staining.
• Satin sheen to concrete
• Zero VOC. Environment friendly material.

• Load bearing for support of arises under heavy wheel load
• Good resistance to chemicals and hydrocarbon fuels
• Excellent adhesion without primer to dry clean concrete
• Pouring grade ensures ease of placing
• Suitable for use in wide joints
• Self levelling to produce uniform and neat joints

• Approved for use in contact with potable water.
• Withstands high positive and negative hydrostatic pressures
• Excellent crack accommodation after immersion. 
• Excellent bond to concrete and masonry. 
• Long working life. 
• Easy application by brush, roller, trowel or spray. 
• Bonds to green or damp concrete. 
• Effective barrier to sulphates and chlorides

Nitocote EP405 is a two pack, solvent free, epoxy resin material.  It is supplied in pre-measured quantities ready for site mixing and use.  The material cures to provide a smooth, hygienic and tough fi nish which is suitable for contact with potable water and foodstuff s.  It is available in blue and white colours.

Uses:

Nitocote EP405 is a two pack, solvent free, epoxy resin material.  It is supplied in pre-measured quantities ready for site mixing and use.  The material cures to provide a smooth, hygienic and tough fi nish which is suitable for contact with potable water and foodstuff s.  It is available in blue and white colours.

Advantages:
Food grade & Hygienic – Suitability to potable water and food stuff  storage.
Compatible with all substrates – Can be applied directly on to mild steel and concrete
Aesthetic – Forms a smooth, glossy and to easy clean surface on curing
Abrasion resistant – Exceptional resistance to abrasion and to a wide range of chemicals Corrosion resistant – Does not contain any metallic particles
Chemical resistant – Proven against a wide range of industrial  chemicals
Solvent free & Non – toxic - No odour during application and can be used in confi ned areas.

• Advanced Technology : New generation molecule yields high performance concrete. Suitable for any grade of concrete including higher grades.
• Corrosion resistant: Meets the requirements of Japanese code JIS Z1535 (modifi ed) fi rst of kinds in the integral water proofi ng range.
• High Strength : Due to better dispersion of cement particles and helps in the better degree of hydration yielding high strength compared to control.
• Cohesive Mix : Improves workablity and cohesiveness of the concrete.
• Durability : Improves durability due to reduction in permeability of concrete and corrosion resistance of steel.

We have emerged as one of the leading names of Lokfix Anchor . Clients can avail the offered product from us at the most reasonable prices.

Features:

• Non toxicity

• Accurate composition

• Tempera proof packaging

Hydroproof Xtra is Single component acrylic polymer for cement based waterproof composite coating membrane. 

Uses
Provides an effective and economical method of waterproofing to concrete and masonry surfaces, by mixing with cement and application by brush.

Advantages

• Non - toxic, non-flammable and user friendly
• Provides a tough, impermeable waterproof membrane
• It Can be applied by brush, on horizontal and vertical surfaces
• Excellent adhesion to concrete and masonry surfaces
• Protects concrete and mortar from natural elements such as wind, rain, sunlight Breathable - allows inside water vapour to escape

• Single application : Forms moisture barrier
• No other curing necessary : Eliminates use of water, hessian or sand completely.
• Reliable : No risk of erratic or poor curing and ensures that cement hydrates effi ciently.
• Ensures hard-wearing surface : Minimises risk of drying shrinkage, cracks and dusty surfaces.
• Easy and safe spray application: Non-toxic and nonfl ammable.

• Adhesion to most common building materials 
• Single component with fast rate of cure
• Damp surface tolerant
• Non shrink
• Non staining
• High movement accommodation, MAF up to 50%
• Easy to apply
• UV resistant
• Primerless for most applications (see “Priming”)

Fosroc Brushbond RFX is a high-performance, polymer-modified, cementitious waterproof coating designed to provide long-lasting protection for concrete and masonry surfaces. Engineered for superior flexibility and crack-bridging capability, Brushbond RFX forms a tough, seamless, and durable waterproof barrier ideal for both internal and external applications.

This two-component waterproofing system offers excellent adhesion, UV stability, and resistance to water ingress, making it one of the most reliable solutions for terraces, balconies, water tanks, basements, bathrooms, and other wet areas. It ensures long-term durability and protection even under harsh weather conditions.

• Advanced Technology : New generation molecule yields high performance concrete. Suitable for any grade of concrete including higher grades.
• Corrosion resistant: Meets the requirements of Japanese code JIS Z1535 (modifi ed) fi rst of kinds in the integral water proofi ng range.
• High Strength : Due to better dispersion of cement particles and helps in the better degree of hydration yielding high strength compared to control.
• Cohesive Mix : Improves workablity and cohesiveness of the concrete.
• Durability : Improves durability due to reduction in permeability of concrete and corrosion resistance of steel.

1. Medium Fast setting - Minimum disruption to traffic
2. Easy to use - Needs only the addition of water.
3. Easy to lay - Very easy to apply and finish
4. Non shrink - Does not crack
5. High adhesion - Use Nitobond AR as primer ensures good bonding to concrete substrates. Durable & Tough surface - Resistant to wear and tear

• Meets key international standards
• Forms a tough, elastic, rubber-like seal
• Accommodates continuous and pronounced cyclic movement
• Excellent adhesion to most common substrates, including primed concrete, glass, aluminium and stainless steel
• High resistance to ageing reduces physical damage due to climatic extremes

Nitocote EP140 coating is based on solvented epoxy resins specially formulated to provide a durable coating suitable for application to both vertical and horizontal surfaces. It cures to form a smooth hygienic film with good resistance to a wide range of mineral and organic acids, fats, alkalis and oils.

Uses
Nitocote EP140 is used as a hygienic and chemical resistant coating for steel tanks, concrete walls, concrete and metal columns, sluices and ducts.

Advantages

• Excellent adhesion - Compatible with all substrates. Can be applied directly on to mild steel and concrete
• Hygienic & Aesthetic – Forms a smooth, glossy and easy to clean surface on curing
• Chemical resistant – Proven against a wide range of industrial chemicals

• Penetrates into substrates
• Non staining 
• Reduces water and chloride intrusion 
• Increases freeze thaw resistance 
• Minimises effloresence
• Allows water vapour to escape from the structure
• Resistant to atmospheric contaminants

Lokfix is produced in two versions. The two versions of Lokfix are all pre-measured, two part, filled polyester resin grouts. After hardening, the grout produces anchorages of consistent reproducible values. The versions are:

Lokfix S - used where hole diameter is less than 25 mm greater than the bar diameter.Lokfix P - used in overhead or horizontal holes where bar/hole relationship conforms to Lokfix S. The thixotropic nature of Lokfix P reduces flow of grout out of the hole.

UsesLokfix mix and place grouts are used for high strength corrosion resistant anchoring of bolts and bars from 12-51 mm diameter into concrete, rock, masonry or brickwork where high speed of installation and early application of load is required.Permanent installation of reinforcement starter bars, foundation bolts, base plates, balustrading, barriers and safety fences, railway tracks, tie-back anchors, reinforcement dowelling abutments, ground anchors for towers, cranes, dock sills etc.

Advantages

• Rapid strength gain.
• Vibration resistant.
• Corrosion resistant.
• Non-expansive.
• Can be placed underwater

• Active ‘Zinc-rich’ system combats corrosion by electro chemical means.
• Formulated for use with Nitocote protective coatings and enamel paints
• Two component product - easy to mix and use.